Washer Bottle, Pump, Line & Nozzle
-
Hex Lock/Conelock Nut 7/16 UNF
Expected ship date:Next Business DayRegular Price: AU$1.50
Special Price AU$1.35
Each -
Hi-Performance / Hi-Flow Thermostat - V8 (160-Deg)
mr. gasket high-performance thermostats are designed to resist large variations in coolant pressures that can occur at high rpms. under these conditions, coolant temperature and pressure fight for control of... Learn MoreExpected ship date:Next Business DayRegular Price: AU$66.05
Special Price AU$62.75
Each -
High Temperature Ceramic High/Low H4 Wiring Loom
This high quality ceramic H4 plug is perfect for use with high wattage globes. Supplied with removable plastic sleeve. Learn MoreExpected ship date:Next Business DayRegular Price: AU$16.00
Special Price AU$15.20
Set of 2 -
High Tensile Bolt : 5/8 UNF (4" Length) Black
Expected ship date:Next Business DayRegular Price: AU$9.00
Special Price AU$8.10
Each -
High Tensile Bolt : 7/16 UNF (4" Length) Black
7/16 x 4 UNF High Tensile Bolt Only Black Learn MoreExpected ship date:Next Business DayRegular Price: AU$9.00
Special Price AU$8.10
Each -
High Torque Starter Motor (2.5HP, 10 tooth) : suit Hemi 6 / Slant 6 / Small Block LA / Big Block B/RB (suit 122 & 130 tooth ring gear)
Our new high torque starter motors boast a huge 2.5 horsepower, and is around just half the size of a factory fitted unit. Learn MoreExpected ship date:Next Business DayRegular Price: AU$199.00
Special Price AU$189.05
Each -
High Torque Starter Motor (2.5HP, 9 tooth) : suits Hemi 6, Slant 6, Small Block, Big Block (with 148 tooth ring gear)
Direct bolt in replacement, no wire adapters required ** These direct fit all new high torque starter motors boast a huge 2.5 horsepower, whist being nearly half the size of... Learn More -
High Voltage Warning Decal : CL/CM
This decal was located on the left-side upper inner guard in the engine compartment, next to the electronic control module. this is a reproduction of the factory-fitted decal found on... Learn MoreExpected ship date:Next Business DayRegular Price: AU$12.00
Special Price AU$10.80
Each -
High Volume Water Pump (alloy) : suit Small Block 273 / 318 / 340 / 360 /408
The 8 impeller design on this water pump is a highly efficient replacement for your Small Block pumping more water than the standard 6 impeller design. Learn More -
High-Low Dipper Switch: suit RV1/SV1/AP5/AP6/VC/VE/VF/VG/VH/VJ
Factory-correct hi-beam dipper switch for use in RV1-VJ vehicles. No modifications required to your factory wiring. Learn More -
Holley 1BBL AP5/AP6 Carburetor (remanufactured, suit cable)
As found on AP5 and early AP6 vehicles fitted with a 225 Slant 6 engine running accelerator cable (not linkage.) Supplied with brand new vac pot - not reconditioned. High... Learn More -
Holley 1BBL Carburetor (remanufactured, suit cable) fits assorted 1975 Dodge Plymouth
As found on many 1975 Dodge Plymouth with 225 Slant 6 engines (see full list below) Supplied with brand new vac pot - not reconditioned. High quality re-manufacture from the... Learn More -
Holley Adjustable Fuel Pressure Injection Regulator (suit EFI 15-60psi)
Holley adjustable fuel injection regulators are able to provide all of the fuel pressure that your high performance, fuel injected vehicle will require. They utilize a special wave spring to... Learn More -
Holley Classic Holley Carburetor : 750 CFM : 4 Barrel : Vacuum Secondaries (Shiny finish)
One of the most widely used Holley carbs of all times -the 0-80508S. Its dual feed fuel inlets assure you get all the fuel you need, and its 750 CFM... Learn More -
Holley Inline Fuel Pressure Regulator : 4.5-8 PSI
The needle and seat assemblies that are installed in most carburetors can sufficiently control fuel pressure up to about 8 psi. If the fuel pump is putting out more than... Learn More